S SAIMEIYA Cosmetic Manufacturing
S SAIMEIYA Cosmetic Manufacturing
PET, PETG and PP Bottles Compared
Home/ Encyclopedia/ Materials

PET, PETG and PP Bottles Compared

Three clear-looking resins behave very differently with alcohol, fragrance and a squeeze. Clarity, barrier and the recycling stream usually decide the choice before price does.

Materials 4 min read 19 Nov 2026

Key takeaways

  • PET gives the best clarity and oxygen barrier of the three at the lowest weight.
  • PETG resists impact better but can stress-crack with concentrated alcohol or fragrance.
  • PP tolerates alcohol and essential oils, but reads hazy and loses fragrance faster.
  • PETG contaminates the PET recycling stream, so check the market before specifying it.
  • For leak complaints, wall thickness and closure torque matter more than resin choice.

Three resins, one shelf. PET, PETG and PP bottles all look like clear plastic to a buyer, and they behave differently enough that the choice is usually made by the formula rather than the price list. Clarity, barrier, chemical resistance and the local recycling stream are the four variables that matter.

1. Three resins, three briefs

Clear bottle, squeezy bottle and premium bottle are three different briefs, and the resin follows the brief. PET is stiff, clear and light. PETG is clearer still and tougher but softer. PP is hazy, flexible and chemically tolerant. Choosing on price alone usually lands on the wrong one, and the saving reappears as a reformulation cost.

2. Clarity and the shelf

PET and PETG both read water-clear; PP is translucent at best unless clarified, and clarified PP still carries a slight haze in thick sections. Under retail backlighting the difference is visible at a metre. If the formula is opaque anyway, clarity stops mattering and the decision moves to cost and chemical resistance.

3. Chemical resistance and crazing

Concentrated alcohol, some fragrance components and citrus oils attack PETG under stress, producing crazing that starts at a base corner and spreads. PET resists better but is not immune. PP tolerates most of these comfortably. A compatibility fill to the shoulder, stored at 40 degrees for four weeks, shows crazing that a room-temperature check misses.

4. Barrier and fragrance loss

PET has a lower oxygen transmission rate than PP, which matters for oils, vitamin C and any fragrance that fades. PP loses top notes faster across a twelve-month shelf life, and the loss is often blamed on the formula. Where fragrance retention is central, a barrier layer or a different resin is cheaper than over-dosing the fragrance. A barrier coating applied at the preform stage is the usual compromise.

5. Weight and wall thickness

A 200 ml PET bottle typically weighs 18 to 28 grams; the same volume in PP often runs 25 to 40 grams because the wall must be thicker to hold shape. PETG sits between. Lighter is cheaper to ship and usually cheaper to make, but a thin wall flexes under a pump and can crack at the neck thread, so weight reduction has a floor.

6. Two processing routes

PET bottles are usually injection stretch blow moulded, which orients the polymer and gives strength from a thin wall. PP is usually extrusion blown, which is cheaper for short runs but gives less control over wall distribution. PETG runs on either route. The route sets tooling cost and minimum order, so it belongs in the first conversation.

7. Tooling and cost per unit

Per unit, PET is often cheapest at volume and PP cheapest at low volume, because extrusion tooling costs less. A stretch blow mould can run several thousand dollars per cavity, which only makes sense above a few tens of thousands of units a year. Ask for the tooling figure separately so the comparison stays honest. Amortised over three years, tooling is rarely the deciding number.

8. Recycling and market fit

PET is the most widely collected plastic bottle stream, and clear PET is the most valuable. PETG is not collected separately and can contaminate a PET stream, so several markets treat a PETG bottle as non-recyclable in practice. PP is collected in a growing number of systems with a lower yield. Check the destination market, not the material’s reputation.

9. The questions that decide it

Is the formula alcohol-based? Does it need to squeeze? Is clarity a retail requirement? What is the annual volume? Will it ship to a market with a deposit return scheme? Answer those five and the resin usually chooses itself. Where two still fit, run a four-week compatibility fill on both before committing to tooling.

10. Where it fits

Bottle choice shapes how body wash and facial essence reach the customer. Material comparisons continue in encyclopedia.

Reference: Primary pack material notes, 2025

Start a project

Ready to put your name on a formula?

Send a brief and our formulation team will come back with a costed proposal, sample plan and timeline — typically within two working days.

WhatsApp +86 13149918467
WeChat QR code Scan to add WeChat
Call +86 13149918467 [email protected]
Quote WhatsApp Call Products