S SAIMEIYA Cosmetic Manufacturing
S SAIMEIYA Cosmetic Manufacturing
Serum Wet-Out on Sheet Mask Substrates
Home/ Encyclopedia/ Materials

Serum Wet-Out on Sheet Mask Substrates

Pale patches on a saturated mask are a wetting problem. Surface tension, substrate critical wetting tension, viscosity and the load figures that keep a sheet even.

Materials 4 min read 16 Nov 2026

Key takeaways

  • Water at 72 mN/m will not wet a substrate whose critical wetting tension is 30-45 mN/m.
  • Wetting agents work at 0.1-0.5%; overdosing foams, underdosing shows as pale patches.
  • A serum in the low hundreds of mPa·s wicks far faster than a 3,000 mPa·s gel.
  • Typical load is 3.5-5 times dry sheet weight, with a 30-120 second dwell before sealing.
  • Serum in the seal zone causes leakers, so target slightly below full saturation.

Dry patches on a saturated sheet mask are a wetting problem, not a fill-volume problem. The serum has to displace air from a porous substrate against surface tension, and the speed at which it does that decides whether a mask looks evenly loaded on the line and on the face.

1. The Symptom and the Wrong Fix

The sachet contains the right weight, the sheet is wet at the edges, and the centre is pale. The instinct is to add serum, which raises cost and produces dripping. The actual issue is that the liquid has not penetrated the fibre structure, and more liquid will not force it in.

2. Surface Tension in Plain Terms

Water sits near 72 mN/m at room temperature. Most nonwoven substrates have a critical wetting tension in the 30-45 mN/m range, so unmodified water beads rather than wicks. A surfactant that drops surface tension below that threshold turns the substrate from hydrophobic to wettable within seconds, and the effect is permanent for that substrate batch.

3. Wetting Agents and Dose

Polysorbates, PEG-based wetting agents and some glycols reduce surface tension effectively at 0.1-0.5%. Overdosing produces foam on the line and a tacky residue after drying. Underdosing shows as pale patches that appear after the sachet has been stored for a few days, not on the fill day.

4. Substrate Differences

Spunlace cotton and viscose blends wet readily. Cupro is denser and slower. Bio-cellulose is a hydrogel-like network that absorbs well but releases slowly, so it feels drier at first contact. A serum optimised for one substrate can look under-filled on another at the same weight.

5. Viscosity Against Wicking

Wicking depends on pore size and liquid viscosity. A serum at 3,000 mPa·s penetrates far more slowly than one at 300 mPa·s. Most sheet mask serums sit in the low hundreds for this reason. Thickening to improve the hand feel is the most common cause of a wet-out problem.

6. Fill Ratio and Dwell Time

Typical load is 3.5-5 times the dry sheet weight, with the sheet and the residual serum weighed separately. After filling, a short dwell before sealing, usually 30-120 seconds, lets the liquid distribute. Skipping the dwell produces sachets that look correct and open unevenly a month later.

7. Testing Wet-Out Objectively

Weigh the sheet before and after a controlled soak, then press it between two filter papers and measure the transferred liquid. Photograph the sheet on a light box at a fixed exposure. Both methods catch differences that the eye misses under line lighting, and both give a number that a second site can compare against without an argument about appearance.

8. The Other Side: Over-Wetting

A fully saturated sheet drips during unfolding, wets the seal area and causes leakers. Serum in the seal zone is a filling defect that surfaces later as a transport complaint. Target an even distribution slightly below saturation rather than the maximum the substrate will hold.

9. What to Put in the Specification

Record substrate and grade, sheet weight per unit area, target serum load, viscosity range at 25 C, surface tension of the finished serum and the dwell time before sealing. Those six numbers let a second site reproduce the result without a visit.

10. Where it fits

Wet-out is a materials question with a formulation answer. Compare substrates in the encyclopedia, read line notes in news, and see the formats in products. For sheet and hydrogel formats such as sheet masks, specify load and viscosity together.

Reference: Materials and substrate evaluation notes, 2025

Start a project

Ready to put your name on a formula?

Send a brief and our formulation team will come back with a costed proposal, sample plan and timeline — typically within two working days.

WhatsApp +86 13149918467
WeChat QR code Scan to add WeChat
Call +86 13149918467 [email protected]
Quote WhatsApp Call Products