S SAIMEIYA Cosmetic Manufacturing
S SAIMEIYA Cosmetic Manufacturing
Viscosity Numbers: Spindle, Speed, Temp
Home/ Encyclopedia/ Quality

Viscosity Numbers: Spindle, Speed, Temp

A viscosity value means nothing without spindle, speed and temperature. Most supplier and buyer disagreements on thickness come down to three settings that were never written down.

Quality 4 min read 18 Nov 2026

Key takeaways

  • A viscosity figure without spindle, speed and temperature cannot be compared with anything.
  • Temperature moves the reading by several percent per degree on many emulsions.
  • Read after a fixed interval, typically 30 to 60 seconds, once the dial stabilises.
  • Thixotropic products need an up-and-down curve, not a single point.
  • Rheometers give shear rate; viscometers give a number that only matches itself.

1. A number is not a specification

“20,000 cP” describes a reading taken on one instrument, with one spindle, at one speed, at one temperature. Change any of the four and the number moves, sometimes by a factor of two. A specification written that way cannot be met consistently by a second lab, and it cannot be defended when a buyer tests the same lot and gets a different value. The settings are part of the specification, not a footnote.

2. Spindle and speed set the shear

On a rotational viscometer, the combination of spindle and speed defines the shear rate applied to the sample. A small spindle at high speed shears the product harder than a large spindle at low speed, so a shear-thinning cream reads lower. Most factories settle on one spindle and speed per product family and never vary it, which is the right approach for routine release testing.

3. Temperature moves the number

Many emulsions change viscosity by 3 to 8 percent per degree Celsius near room temperature. A sample measured at 22 degrees and one at 26 degrees can differ by 20 percent with no difference in the product. Control the sample to 25 degrees plus or minus 0.5 in a water bath, and record the actual temperature next to the reading.

4. When to read

The dial keeps falling for the first twenty to sixty seconds as the spindle creates a channel in the sample. Read at a fixed interval, usually thirty or sixty seconds, and always the same one. Reading when the needle “looks steady” introduces operator variation that looks exactly like batch variation on a trend chart.

5. Thixotropy and the loop

Products that rebuild structure after shearing need an up-and-down speed ramp rather than a single point. Run the speed up in steps, then back down, and compare the two curves. The gap between them is the thixotropic area, which predicts how the product behaves on a filling nozzle and how it settles in a jar. A single value hides all of it.

6. Viscometer or rheometer

A viscometer gives a relative number that is excellent for release testing and useless for predicting flow in an unfamiliar process. A rheometer gives shear rate and shear stress, which allows comparison with filling and pumping conditions. Use the viscometer for routine control and borrow rheometer time when a formula changes or a line problem needs explaining.

7. Writing a usable specification

State the instrument model, spindle, speed, temperature, equilibration time and reading interval, then give a range based on at least twenty lots. A range of plus or minus 15 percent around the mean is common for emulsions. Anything tighter needs process capability data to support it, and anything wider than 25 percent is not controlling anything.

8. Comparing supplier and factory

When a brand owner’s lab and the factory disagree, compare settings before comparing results. In most cases the two labs are using different spindles or reading at different times, and both are correct within their own method. Agree one method in writing and, where possible, exchange a retain sample so both labs test the same material.

9. Common misreads

Testing a sample straight from the filling nozzle while it is still warm, testing a sample that was not equilibrated after transport, and testing the surface of a settled jar instead of a mixed sample are the three errors that produce most spurious results. Each is cheap to prevent and expensive to explain after a rejected shipment.

10. Where it fits

Viscosity control supports every format we fill, from body wash to AHA BHA serum. The encyclopedia index covers related test methods, and products lists the ranges involved.

Reference: Quality control SOP notes, 2025

Start a project

Ready to put your name on a formula?

Send a brief and our formulation team will come back with a costed proposal, sample plan and timeline — typically within two working days.

WhatsApp +86 13149918467
WeChat QR code Scan to add WeChat
Call +86 13149918467 [email protected]
Quote WhatsApp Call Products