S SAIMEIYA Cosmetic Manufacturing
S SAIMEIYA Cosmetic Manufacturing
HLB and Emulsifier Blends: The Numbers
Home/ Encyclopedia/ Formulation

HLB and Emulsifier Blends: The Numbers

Required HLB is arithmetic, but stability is not. The weighted oil-phase value gets you close, and the interfacial film, fatty alcohol network and electrolyte load decide whether the cream holds.

Formulation 4 min read 19 Nov 2026

Key takeaways

  • Required HLB is the weighted average of each oil's value across the oil phase.
  • Two emulsifiers blend linearly, so a pair can be tuned to almost any target value.
  • A matched HLB still fails when the interfacial film is weak or the phases are unbalanced.
  • A fatty alcohol plus a low-HLB emulsifier builds a lamellar network that adds yield value.
  • Electrolyte and pH tolerance must be tested; the HLB number predicts neither.

The HLB number is arithmetic anyone can do in a minute; stability is not. Getting the required value right puts you in the right neighbourhood, and the interfacial film, the fatty alcohol network and the electrolyte load then decide whether the cream is intact at week eight.

1. What the number describes

Hydrophilic-lipophilic balance is a scale from 0 to 20 describing how water-loving an emulsifier is. Low values favour water-in-oil systems, high values favour oil-in-water. It is shorthand for the balance of the molecule rather than a measure of quality, and two emulsifiers with the same number can behave quite differently at an interface.

2. Calculating the required value

Each oil has a required balance value, and the blend’s requirement is the weighted average of its components. An oil phase of 70 percent of a requirement-7 oil and 30 percent of a requirement-12 oil needs about 8.5. Work it out before choosing emulsifiers, and note that waxes, silicones and fragrances often need a value established by trial rather than from a table.

3. Blending two emulsifiers

Two emulsifiers mix linearly by weight, so a pair at 4 and 15 can hit any value between them. A ratio of three or four to one in favour of the higher-value component is a common starting point for a stable cream. The blend also broadens tolerance, because a single emulsifier sits exactly at the balance point where small changes tip the system.

4. Why a match is not enough

Two systems can hit the same required value and behave completely differently, because the balance point says nothing about the strength of the interfacial film. A rigid film resists coalescence; a loose one does not. That is why pairing a small hydrophilic emulsifier with a fatty alcohol or a high-molecular-weight co-emulsifier matters more than the arithmetic.

5. Ionic and non-ionic behaviour

Non-ionic emulsifiers stabilise by steric hindrance and tolerate electrolyte reasonably well. Anionic ones add electrostatic repulsion and stabilise strongly but are sensitive to salt and low pH. Cationic systems work well on skin and hair and are incompatible with anionics. The choice restricts which actives and preservatives can share the formula. Where the formula contains a salt-sensitive thickener, the emulsifier follows the thickener.

6. Lamellar networks

A fatty alcohol such as cetearyl alcohol combined with a low-balance glyceryl stearate forms a lamellar gel network in the water phase. The network holds water, gives yield value and makes the cream feel rich without a polymer. It also slows droplet movement, which is why many market creams stay stable on a modest emulsifier level.

7. Electrolyte and pH tolerance

Salt, acidic actives and buffers all change how an emulsifier behaves at the interface. Systems stabilised mainly by a lamellar network usually tolerate more electrolyte than systems relying on a single emulsifier. Test at the extremes of your pH range and at the highest electrolyte load the formula could see, rather than at the nominal point only.

8. Starting ranges that work

Oil-in-water creams commonly sit between 10 and 12, lotions slightly lower, water-in-oil systems between 4 and 6. Total emulsifier is often 2 to 5 percent with another 2 to 4 percent of fatty alcohol. These are starting points for a trial, not a formula. Adjust the pair rather than the total when stability is marginal. Record the pair, not just the total, or the next trial starts from scratch.

9. How to test the result

Microscopy at day one and after four weeks at 40 degrees shows droplet size and whether coalescence is underway. Conductivity confirms the continuous phase. A centrifuge run at 3,000 rpm for 30 minutes is a fast screen for separation. Viscosity change over four weeks shows whether the network is holding. Four cheap tests cover most failures.

10. Where it fits

Emulsifier balance underlies every cream and lotion we fill. Formulation notes continue in encyclopedia.

Reference: Formulation development notes, 2025

Start a project

Ready to put your name on a formula?

Send a brief and our formulation team will come back with a costed proposal, sample plan and timeline — typically within two working days.

WhatsApp +86 13149918467
WeChat QR code Scan to add WeChat
Call +86 13149918467 [email protected]
Quote WhatsApp Call Products