S SAIMEIYA Cosmetic Manufacturing
S SAIMEIYA Cosmetic Manufacturing
Cold-Process Emulsions: When They Work
Home/ Encyclopedia/ Formulation

Cold-Process Emulsions: When They Work

Cold processing saves hours and energy but narrows the raw material list. Emulsifier solubility, oil melting point and air entrapment decide whether the shortcut produces a cream or a problem.

Formulation 4 min read 20 Nov 2026

Key takeaways

  • Cold process needs emulsifiers that function at room temperature without a melt phase.
  • Liquid oils and low-melting esters suit the method; solid butters and waxes do not.
  • Energy and cycle time typically fall by half or more against a hot process.
  • Air entrapment is the main quality risk, since there is no heat to drive bubbles out.
  • Preservation must be validated on cold bulk, because no heat step reduces the load.

Cold processing an emulsion saves energy and hours, but it works with a narrow set of raw materials. Emulsifiers must be liquid or readily dispersible at room temperature, and the oil phase has to stay fluid without melting. Where those conditions hold, the savings are real and repeatable.

1. What cold process means

Both phases are combined at or near room temperature, usually between 20 and 30 degrees, and the emulsion forms through mechanical energy rather than thermal phase inversion. Nothing is heated and nothing needs to cool. The result is a shorter cycle and a lower energy bill, bounded by which raw materials the formula can use.

2. Emulsifiers that tolerate it

Cold-process emulsifiers are typically liquid at room temperature or easily dispersible, with a low melting point and good solubility in the continuous phase. Polymeric emulsifiers and some phosphate esters perform well. A traditional fatty alcohol and ethoxylate pair that needs a melt phase will produce a coarse, unstable emulsion if forced cold. Cold processing does not rescue a formula that was designed around heat.

3. Which oils fit

Liquid oils, low-melting esters and silicone fluids disperse easily. Shea butter, cocoa butter and solid fatty alcohols need heat to melt and recrystallise unpredictably if added cold. A formula carrying 8 percent solid butter cannot be made cold without a pre-melt, and a pre-melt removes most of the energy saving that justified the change. Where the brief insists on a butter, treat the process as hot and stop counting the saving.

4. Thickening without heat

Cold creams rely on pre-neutralised carbomer dispersions, xanthan, or associative thickeners that build on shear. Hydrating powdered carbomer cold is slow and prone to lumps, so many plants use a pre-dispersed grade. Build viscosity after emulsification, not before, or the emulsion forms inside a thick matrix and stays coarse.

5. Preservation on cold bulk

A hot process gives an incidental reduction in microbial load; a cold process does not. The preservative therefore carries the whole burden, and the challenge test must run on bulk made the cold way. Where a product claims preservative-free, cold processing is usually the wrong route unless water activity or pH control does the work.

6. Air entrapment

Without heat, air stays in the bulk. It shows as a lighter fill weight, a spongy texture and, in a clear gel, visible bubbles. Mix under vacuum where equipment allows, keep the head below the surface and never cascade the oil phase into the water. De-aerating for twenty minutes before filling is often enough to clear it, and a slower agitator speed near the surface helps more than a longer vacuum cycle.

7. Where the saving comes from

Heating and cooling energy disappear, and the cycle shortens by the time a tank would take to heat and cool, often two to four hours on a two tonne batch. The trade is a narrower raw material list. On a large batch the saving is significant; on a 200 kilogram batch it is modest and may not justify the reformulation.

8. Scale-up behaviour

A cold process is more sensitive to mixing energy than a hot one, because no thermal driving force helps the emulsion form. Lab homogenisers deliver far more shear per kilogram than a production agitator, so a lab sample can look perfect while a tank batch comes out coarse. Scale by tip speed rather than by revolutions per minute.

9. When hot process is right

Choose hot when the formula needs solid butters, waxes or fatty alcohols, when thermal phase inversion is the intended mechanism, or when the product must be filled hot for microbial reasons. Cold process constrains the formula rather than improving it universally, and pretending otherwise produces samples nobody can reproduce at scale. Match the method to the raw materials the brief actually needs.

10. Where it fits

Cold-process systems suit our body lotion and facial essence formats. Related formulation notes continue in encyclopedia.

Reference: Formulation development notes, 2025

Start a project

Ready to put your name on a formula?

Send a brief and our formulation team will come back with a costed proposal, sample plan and timeline — typically within two working days.

WhatsApp +86 13149918467
WeChat QR code Scan to add WeChat
Call +86 13149918467 [email protected]
Quote WhatsApp Call Products