S SAIMEIYA Cosmetic Manufacturing
S SAIMEIYA Cosmetic Manufacturing
Hyaluronic Acid Grades and Molecular Weight
Home/ Encyclopedia/ Ingredients

Hyaluronic Acid Grades and Molecular Weight

One INCI name covers chains from a few thousand to several million daltons, and the grade decides feel, viscosity, dose and cost. The band matters more than the percentage on the label.

Ingredients 4 min read 19 Nov 2026

Key takeaways

  • One INCI name covers molecules from a few thousand to several million daltons.
  • High molecular weight builds a surface film; low and oligomeric grades feel lighter.
  • Viscosity at a fixed percentage is the quickest proxy for which grade arrived.
  • Heat, extreme pH and contamination reduce chain length in storage without changing assay.
  • Blending two or three grades usually beats a single grade on feel and on cost.

Sodium hyaluronate is one INCI name for a family of chains that differ by three orders of magnitude in length. The grade decides viscosity, use level, feel and cost, and a specification quoting only a percentage leaves the most important variable open.

1. One name, many molecules

Sodium hyaluronate on a label covers a wide family of chain lengths. A high-molecular-weight grade can exceed 1.5 million daltons; an oligomer grade sits under 10,000. Both are the same chemistry and neither is more genuine than the other, but they behave differently on skin, in the bottle and on the cost sheet.

2. The bands in practice

Suppliers usually offer four practical bands: high above roughly 1.5 million daltons, medium between 0.5 and 1.5 million, low between 50,000 and 500,000, and oligomeric below 10,000. Each band has a typical viscosity at one percent in water, and that viscosity is the fastest way to check which one arrived in the drum.

3. Film versus penetration

High-molecular-weight material stays near the surface and forms a water-binding film, which gives immediate smoothness and a measurable reduction in water loss. Low and oligomeric grades are small enough to move into the upper layers, where they support hydration over hours rather than minutes. Marketing often claims penetration for all of them, which is not accurate.

4. Viscosity and dose

One percent of a high grade in water gives a thick gel; one percent of an oligomer gives something close to water. That difference drives the use level: a high grade often appears at 0.1 to 0.3 percent, while an oligomer may need 1 percent or more to matter. Quoting a percentage without the grade says almost nothing about the product. A 0.5 percent load of a medium grade often lands between the two extremes and is the easiest place to start.

5. Sensory trade-offs

High grades feel cushiony at first and tacky as they dry, especially at higher doses or in dry air. Low grades feel lighter and disappear faster. In a serum, a blend of one high and one low grade usually reads better than either alone: the high grade gives body, the low grade gives a dry-down that does not drag.

6. Degradation in storage

The chain breaks down with prolonged heat, extremes of pH and microbial contamination. A serum held at 45 degrees for eight weeks can lose a measurable share of its viscosity, which is chain length falling rather than concentration dropping. A colorimetric assay will not show this; viscosity and size-exclusion chromatography will. Cross-linked grades resist the drop better because the network holds as chains shorten.

7. Verifying the grade

Ask for the molecular weight or the intrinsic viscosity on the certificate, not just the percentage. Measure the viscosity of a one percent solution at 25 degrees against a reference. If a supplier cannot state a band, treat the material as unspecified and test it yourself before it enters a stability programme.

8. Blending grades

Two or three grades at defined ratios give a film that holds water and a dry-down that feels light, often at lower total cost than a single premium grade. Typical ratios run from one part high to one part low, up to one to three. Fix the ratio in the formula and specify each grade, or a supplier substitution will change the feel.

9. Claim discipline

Multi-weight and cross-linked are defensible descriptions of what is in the bottle. A claim that a high-molecular-weight grade penetrates deeply is not, and any claim of a specific percentage effect depends on the grade and the vehicle. Describe the mechanism you can support with a measurement and leave the rest to the consumer’s experience. Consumers describe feel reliably and mechanisms poorly, so a sensory panel is legitimate evidence.

10. Where it fits

Hyaluronic grades appear across our facial essence and AHA BHA serum formats. Ingredient notes continue in encyclopedia.

Reference: Ingredient sourcing notes, 2025

Start a project

Ready to put your name on a formula?

Send a brief and our formulation team will come back with a costed proposal, sample plan and timeline — typically within two working days.

WhatsApp +86 13149918467
WeChat QR code Scan to add WeChat
Call +86 13149918467 [email protected]
Quote WhatsApp Call Products